Camshaftless Technology on Internal Engines

##plugins.themes.bootstrap3.article.main##

  •   Van Viet Pham

Abstract

Along with the development of internal combustion engines, camshafts have also been developed to optimize engine performance. In all types of internal combustion engines, the crankshaft is connected to the camshaft via a toothed belt, chain or pinion. When the crankshaft turns, the camshaft spins and opens and closes the intake and exhaust valve respectively. However, in this non-camshaft engine technology, each intake and exhaust valve will be integrated with an electronically controlled hydraulic pump unit. This system provides a unique ability to independently control intake and exhaust valves. For any engine load, load and discharge times can be programmed independently. The decision system is based on driving conditions, used to maximize performance or minimize fuel consumption and emissions. This allows a greater degree of control over the engine which in turn provides significant performance benefits. This article presents reviews of camshaftless technology developed by VALEO. It is a system that uses solenoid valves to open and close the valve. The solenoid valve will be mounted right on top of the valve inside the engine. The author can see that the technology using this electronic control valve will help reduce the fuel consumption of the engine.


Keywords: Valve Actuation, VALEO, Camless Engines

References

A. T. Hoang and V. V. Pham, “A study of emission characteristic, deposits, and lubrication oil degradation of a diesel engine running on preheated vegetable oil and diesel oil,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 41, no. 5, pp. 611–625, 2019.

A. T. Hoang and V. V. Pham, “Impact of jatropha oil on engine performance, emission characteristics, deposit formation, and lubricating oil degradation,” Combust. Sci. Technol., vol. 191, no. 03, pp. 504–519, 2019.

V. V. Pham and D. T. Cao, “A brief review of technology solutions on fuel injection system of diesel engine to increase the power and reduce environmental pollution,” J. Mech. Eng. Res. Dev., vol. 42, no. 01, pp. 01–09, 2019.

J. Fan, D. Wang, and L. Kang, “Development of renewable biomass energy by catalytic gasification: Syngas production for environmental management,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 40, no. 24, pp. 2941–2947, 2018.

A. T. Hoang and V. V. Pham, “A review on fuels used for marine diesel engines,” J. Mech. Eng. Res. Dev., vol. 41, no. 4, pp. 22–32, 2018.

A. T. Hoang, Q. V. Tran, A. R. M. S. Al-Tawaha, V. V. Pham, and X. P. Nguyen, “Comparative analysis on performance and emission characteristics of an in-Vietnam popular 4-stroke motorcycle engine running on biogasoline and mineral gasoline,” Renew. Energy Focus, vol. 28, pp. 47–55, 2019.

A. T. Hoang, A. T. Le, and V. V. Pham, “A core correlation of spray characteristics, deposit formation, and combustion of a high-speed diesel engine fueled with Jatropha oil and diesel fuel,” Fuel, vol. 244, pp. 159–175, 2019.

A. T. Hoang, V. V. Le, V. V. Pham, and B. C. Tham, “An investigation of deposit formation in the injector, spray characteristics, and performance of a diesel engine fueled with preheated vegetable oil and diesel fuel,” Energy Sources, Part A Recover. Util. Environ. Eff., pp. 1–13, 2019.

A. T. Hoang, M. M. Noor, and X. D. Pham, “Comparative Analysis on Performance and Emission Characteristic of Diesel Engine Fueled with Heated Coconut Oil and Diesel Fuel.,” Int. J. Automot. Mech. Eng., vol. 15, no. 1, pp. 5110–5125, 2018.

A. T. Hoang, “Prediction of the density and viscosity of biodiesel and the influence of biodiesel properties on a diesel engine fuel supply system,” J. Mar. Eng. Technol., pp. 1–13, 2018.

V. V. Pham, “Research on the application of Diesel-Rk in the calculation and evaluation of technical and economic criteria of marine diesel engines using the unified ULSD and Biodiesel blended fuel,” J. Mech. Eng. Res. Dev., vol. 42, no. 2, pp. 87–97, 2019.

V. V. Pham, “Analyzing the effect of heated wall surface temperatures on combustion chamber deposit formation,” J. Mech. Eng. Res. Dev., vol. 41, no. 4, pp. 17–21, 2018.

A. T. Hoang, “Waste heat recovery from diesel engines based on Organic Rankine Cycle,” Appl. Energy, vol. 231, pp. 138–166, 2018.

M. K. Yesilyurt, “The evaluation of a direct injection diesel engine operating with waste cooking oil biodiesel in point of the environmental and enviroeconomic aspects,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 40, no. 6, pp. 654–661, 2018.

A. T. Hoang, “A report of the oil spill recovery and treatment technologies to reduce the marine environment pollution,” Int. J. e-Navigation Marit. Econ., vol. 9, pp. 35–49, 2018.

A. T. Hoang and A. T. Le, “A review on deposit formation in the injector of diesel engines running on biodiesel,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 41, no. 5, pp. 584–599, 2019.

W. K. Lai, M. F. Rahmat, and N. A. Wahab, “Modeling and controller design of pneumatic actuator system with control valve,” Int. J. Smart Sens. Intell. Syst., 2012.

A. Elfasakhany, “Investigations on the effects of ethanol–methanol–gasoline blends in a spark-ignition engine: Performance and emissions analysis,” Eng. Sci. Technol. an Int. J., vol. 18, no. 4, pp. 713–719, 2015.

A. T. Hoang and D. N. Cao, “Some methods of reducing NOx components in exhaust gas,” Int. J. Eng. Res. Manag. Stud., vol. 4, no. 5, pp. 11–18, 2017.

M. T. Pham, A. T. Hoang, A. T. Le, A. R. M. S. Al-Tawaha, V. H. Dong, and V. V. Le, “Measurement and prediction of the density and viscosity of biodiesel blends,” Int. J. Technol., vol. 9, no. 5, pp. 1015–1026, 2018.

W. Y. Chan, J. W. E. Teo, Y. P. Peck, R. Chan, and P. E. S. Y. Choo, “Sulphur emission control areas: operational and legal challenges faced by ports and international shipping.,” 2016.

V. V. Pham, “Research and Design an Experimental Model for the Determination of Deposits Formation Mechanism in the Combustion Chamber,” Int. J. Adv. Sci. Eng. Inf. Technol., vol. 9, no. 2, pp. 656–663, 2019.

D. Boullosa-Falces, J. L. L. Barrena, A. Lopez-Arraiza, J. Menendez, and M. A. G. Solaetxe, “Monitoring of fuel oil process of marine diesel engine,” Appl. Therm. Eng., vol. 127, pp. 517–526, 2017.

Z. Dimitrova, M. Tari, P. Lanusse, F. Aioun, and X. Moreau, “Robust control for an electromagnetic actuator for a camless engine,” Mechatronics, 2019.

Y. Yoon and Z. Sun, “Robust Motion Control for Tracking Time-Varying Reference Signals and Its Application to a Camless Engine Valve Actuator,” IEEE Trans. Ind. Electron., 2016.

M. Pournazeri, A. Khajepour, and Y. Huang, “Development of a new fully flexible hydraulic variable valve actuation system for engines using rotary spool valves,” Mechatronics, 2017.

A. T. Hoang and V. D. Tran, “Experimental analysis on the ultrasound-based mixing technique applied to ultra-low sulphur diesel and bio-oils,” Int. J. Adv. Sci. Eng. Inf. Technol., vol. 9, no. 1, pp. 307–313, 2019.

A. T. Hoang et al., “Power generation characteristics of a thermoelectric modules-based power generator assisted by fishbone-shaped fins: Part II–Effects of cooling water parameters,” Energy Sources, Part A Recover. Util. Environ. Eff., pp. 1–13, 2019.

T. Leroy and J. Chauvin, “Control-oriented aspirated masses model for variable-valve-actuation engines,” Control Eng. Pract., 2013.

S. J. Charlton, C. E. Price, J. Rogers, J. W. G. Turner, R. S. Wijetunge, and W. Anderson, “DigitalAir TM Camless FVVA System - Part 2, Gasoline Engine Performance Opportunities,” SAE Int. J. Engines, 2017.

Downloads

Download data is not yet available.

##plugins.themes.bootstrap3.article.details##

How to Cite
[1]
Pham, V. 2020. Camshaftless Technology on Internal Engines. European Journal of Engineering Research and Science. 5, 2 (Feb. 2020), 118-123. DOI:https://doi.org/10.24018/ejers.2020.5.2.1663.